                 Notes for 6502 Project stripboard layouts
                 -----------------------------------------

General
-------
1. The red lines are wires. It's best to use insulated single-core wire
(sometimes called 'bell wire').
2. The copper strips run left-to-right.
3. The little '+' symbols are track breaks. Make sure you don't miss any of
these!
4. The large cross-hairs are mounting holes. You may want to adjust these.
5. PCB connectors (labelled J1, J2 etc) are 0.1" pitch polarised connectors
such as the Molex KK series. Take the square pin in the diagrams as pin 1.

6502 Computer 0799.PCB
----------------------
1. Stripboard size: 46 strips by 138 holes.
2. R7 is the series resitor for the power LED. Adjust as necessary.
3. Connect a 10k linear potentiometer to J9 for the LCD contrast control.
The wiper goes to pin 3.
  J3  1 -------|
              [ ]
              [ ]<--
              [ ]  |
      2 -------|   |
                   |
      3 ------------
4. J7 connects straight to pins 1-6 of a standard HD44780-based LCD display,
and J10 connects to pins 7-14.
5. The reset button is a push-to-make non-latching button connected to J2.
6. J8 connects to a TTL clock generator (max 2MHz).  Pin 1=+5V, pin 2=GND,
pin 3=clock signal. See 'SPG8640 programmable clock module.PCB' and
'2MHz clock module.PCB'.
7. Connect J4 (6502 board) to J1 (I/O board)
           J5              to J2
           J3              to J3
8. You should add 0.1uF decoupling capacitors, between +5V and GND, close to
all the ICs.
9. Use a ZIF socket for U6.

IO Daughterboard 0799.PCB
-------------------------
1. Stripboard size: 39 strips by 79 holes.
2. U3 should have a decoupling capacitor (C7 and C8 provide decoupling for
U1 and U2).
3. J8, J9 and J11 are designed to supply power to external circuits which use
the 6522s.
4. The numbers next to J10 are the pin numbers for a 9-pin D socket (the
RS232 serial port).
5. Note the red '+' signs next to C2-C6 to indicate polarity.
6. U5 is a 1.8432MHz TTL output crystal oscillator module.

2MHz clock module.PCB
---------------------
1. Stripboard size: 7 strips by 11 holes.
2. Sorry that this is so difficult to see in Traxmaker, but you've got to
admit it's a good compact layout. Use the Zoom feature.
3. Notice that one of the legs on each of R1, R2, C1 and C2 has been moved,
with a small yellow line to the component. When you build the board these
components will sit diagonally, not straight as it looks in the diagram.
4. It is easier to use PCB pins instead of a plug and socket to connect to
this board.
5. The wiring is:
    J1 this board    J8 main board
+5V      1                 1
GND      2                 3
CLK      3                 2

SPG8640 programmable clock module.PCB
-------------------------------------
1. Stripboard size: 10 strips by 16 holes.
2. The DIP-switch SW1 should be 6-way, not 7-way. Align it with the bottom
of the outline shown in the diagram.
3. See 'SPG-8640BN.txt' for the frequency settings.
4. It is easier to use PCB pins instead of a plug and socket to connect to
this board.
5. The wiring is:
    J1 this board    J8 main board
+5V      1                 1
GND      2                 2
CLK      3                 3

Keypad interface.PCB
--------------------
1. Stripboard size: 20 strips by 22 holes.
2. There's four track breaks underneath one of the wires - make sure you
don't miss them!
3. Pins 1-8 of J1 connect to a 6522 port, e.g. J4 on the I/O board. You could
connect pins 9-10 to J11 on the I/O board, or any other power source.
4. The letters E to M by J2 refer to the connections on a Secme ECO 16250 06
16-way keypad (Farnell order code 497-212).

-----------------------------------------------------------------------------
Chris Ward <chris.ward@freenet.co.uk>
6502 Project home page: http://home.freeuk.net/c.ward/
